BETTCHER INDUSTRIES Quantum Flex 1000 Operating Instructions/Spare Parts List Download Page 26

Page: 26 / 118

Unpacking and Installation

3-10

Unpacking and Installation

Manual No. 107013

Operating Instructions and Parts List for the Quantum Flex

™

Trimmer

January 1, 2018

ATTACHING QUANTUM FLEX

™

TRIMMER TO THE WHIZARD

QUANTUM

DRIVELINE OR WHIZARD

FLEXSHAFT AND CASING

ASSEMBLY

The Disconnect Casing

•

Hold the trimmer in the hand you will use in operation, and with the other hand, grasp the

Whizard Quantum

driveline or Whizard

flexshaft and casing assembly and push it into

the end of the tool through the handle retaining knob until the latch catches the detent.

•

The disconnect lever rotates freely around the handle.

•

Align the disconnect lever in the notched-out area of the handle. Slightly open the fingers on

the hand holding the trimmer. Push the driveline or flexshaft casing assembly inward and

hold the lever down in the handle groove with the normal operating hand.

•

Check to see that the lever is seated completely flat within the groove.

•

Release the lever and the casing should pop out and stop the blade from turning. The motor

will continue to operate.

DISCONNECT LEVER

Summary of Contents for Quantum Flex 1000























































































































Search results

Summary of Contents for Quantum Flex 1000

Reviews:

Related manuals for Quantum Flex 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Quantum Flex 1000, Operating Instructions/Spare Parts List

Search results

Summary of Contents for Quantum Flex 1000

Reviews:

Related manuals for Quantum Flex 1000

Brands by name

Popular brands