manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex 1000, Operating Instructions/Spare Parts List, Page: 118 / 118

Share
Download
BETTCHER INDUSTRIES Quantum Flex 1000 Operating Instructions/Spare Parts List Download Page 118

Contact and Document Information

8-2

Contact and Document Information

Manual No. 107013

Operating Instructions and Parts List for the Quantum Flex

™

 Trimmer

January 1, 2018

CONTACT ADDRESS AND PHONE

For additional information, technical support and spare parts, contact your Regional Manager, 

Distributor, or Bettcher Representative:

Bettcher Industries, Inc.

BETTCHER GmbH

P.O. Box 336

Pilatusstrasse 4

Vermilion, Ohio 44089

CH-6036 Dierikon

USA

SWITZERLAND

Tel: +1 440/965-4422

Tel: +011-41-41-348-0220

Fax: +1 440/328-4535

Fax: +011-41-41-348-0229

Bettcher do Brasil Comércio de Máquinas Ltda.
Av. Fagundes Filho, 145 Cj 101/102 - São Judas
São Paulo - SP
CEP 04304-010 - BRASIL
Tel: +55 11 4083 2516
Fax: +55 11 4083 2515

DOCUMENT IDENTIFICATION

Copies of this Operation Instruction may be ordered by quoting the Document ID as listed below:

Document ID:

Manual # 107013

Document Description:

Operating Instructions and Spare Parts List

for the Quantum Flex

™

 Trimmer

Issued:

Date: January 1, 2018

Operating Instructions for Quantum Flex

™

 Trimmers may be requested by quoting the model designation 

of the tool. 

SOFTWARE AND DUPLICATION

For more information, contact your local Representative or:

Bettcher Industries, Inc.

Administrative Assistant/Engineering Department

PO Box 336

Vermilion, Ohio 44089

USA

Summary of Contents for Quantum Flex 1000























































































































Reviews:

No comments