BETTCHER INDUSTRIES Quantum Flex 1000 Operating Instructions/Spare Parts List Download Page 57

Page: 57 / 118

Maintenance

Manual No. 107013

Maintenance

5-19

January 1, 2018

Operating Instructions and Parts List for the Quantum Flex

™

Trimmer

MAINTENANCE - WHIZARD

FLEXSHAFT AND CASING

ASSEMBLY (CONTINUED)

Inspection of the Driver Assembly

•

Wipe off excess grease.

•

Inspect the split bearing (#5) for wear or

damage. Replace if required.

•

Slide the knurled cap (#6) forward against

the driver (#7).

•

Wiggle the bushing (#8) sideways to check

for excessive movement. Movement

should be minimal.

•

Slide the bushing (#8) and washer (#9)

forward toward the driver (#7). If the gap

is 1/16" or greater, the driver should be

replaced.

•

Check the coupling cross pin (#10). If there is any free play or movement, replace the driver

assembly.

Installation of the Driver Assembly

•

Clean the threads on the tube and knurled cap.

•

Apply Whizard special grease to split bearing (#3) and bushing (#2).

•

Apply a small amount of Loctite #242 Threadlocker or equivalent to the threads on the

knurled cap (#1).

•

Pull the spring (#4) on the drive end assembly back with one hand and insert the driver

assembly in the tube.

•

Push in and tighten the knurled cap until it is flush with the end of the tube. Pliers may be

used for this however it is not necessary to tighten beyond hand tight.

•

Allow ½ hour dry time for the threadlocker before the assembly is put in service.

Summary of Contents for Quantum Flex 1000























































































































Search results

Summary of Contents for Quantum Flex 1000

Reviews:

Related manuals for Quantum Flex 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Quantum Flex 1000, Operating Instructions/Spare Parts List

Search results

Summary of Contents for Quantum Flex 1000

Reviews:

Related manuals for Quantum Flex 1000

Brands by name

Popular brands