BETTCHER INDUSTRIES Quantum Flex 1000 Operating Instructions/Spare Parts List Download Page 60 | Manualshive

Page: 60 / 118

background image

Maintenance

5-22

Maintenance

Manual No. 107013

Operating Instructions and Parts List for the Quantum Flex

™

Trimmer

January 1, 2018

ASSEMBLY OF HANDPIECE

Handpiece Bearing Installation

•

Push the handpiece bearing in the frame bore

and align the bearing slot with the frame pin.

•

The bearing should go in with minimal effort

and not require pressing.

WARNING

Sharp blades may cause cut injury!

For proper protection of hands, a protective glove should be used when
operating this equipment and during the handling of blades. Metal mesh
gloves are recommended for the free hand.

Keep hands away from moving blade.

WARNING

Inspection of all parts for excessive wear is critical to ensure proper and
safe operation. Vibration or lock-up may occur as a result of the use of
excessively worn parts. Prior to assembly, be sure all parts are clean and
have been inspected for wear.

NOTICE

DO NOT force the bearing in.
If it does not go in, check
frame and bearing for
damage or build-up.

«
...
58
59
60
61
62
...
»

Summary of Contents for Quantum Flex 1000























































































































Reviews:

No comments

Related manuals for Quantum Flex 1000

Brand: T-Drill Pages: 75

Brand: Zeiss Pages: 38

Brand: 3M Pages: 2

Brand: JB-Lighting Pages: 40

Brand: CAIRE Pages: 38

Martin ERA 800 Performance

Brand: Harman Pages: 32

Martin ERA 600 Performance

Brand: Harman Pages: 32

Brand: Hardt Pages: 22

Brand: Sabre Pages: 2

Life/form SmartScope LF01142U

Brand: Nasco Pages: 2

Brand: Nautilus Pages: 17

Brand: Ocutech Pages: 4

Brand: York Pages: 26

Brand: Parkside Pages: 95

Brand: Ranger Products Pages: 6

Brand: Rane Pages: 88

Brand: Haag-Streit Pages: 21

Brand: Zimmer Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands