manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex 1000, Operating Instructions/Spare Parts List, Page: 23 / 118

Share
Download
BETTCHER INDUSTRIES Quantum Flex 1000 Operating Instructions/Spare Parts List Download Page 23

Unpacking and Installation

Manual No. 107013

Unpacking and Installation

3-7

January 1, 2018

Operating Instructions and Parts List for the Quantum Flex

™

 Trimmer

OPTIONAL WHIZARD

®

 MICRO-BREAK HAND STRAP AND 

ADJUSTMENT

The Whizard

®

 Micro-Break Hand Strap has 

been designed to allow the user to relax the 
fingers of the hand between work cycles 
while maintaining control of the trimmer, 
which can be beneficial and may reduce risks 
associated with stress.

The Whizard

®

 Micro-Break Hand Strap 

comes complete with a primary and 
secondary strap. The straps can be adjusted 
for comfort by adjusting the strap length 
using the strap ring at the bottom of the 
handle. If the secondary strap is not needed, 
it can be removed from the strap ring.

NOTE:

 

The primary strap has the grommet 

and will be placed over the threads on the 
grease cup.

•

Remove the grease cup and retaining 

knob from the tool.

•

With the retaining knob removed from 

the handle, place the strap ring over the handle retaining knob.

•

Screw on the handle retaining knob. 

•

Place the grommet of the primary strap over the threads on the grease cup. 

•

Thread the grease cup into the grease ring.

•

Adjust the strap using the strap ring to make the strap shorter or longer.

NOTICE

Tighten firmly but take care not to over tighten or the handle will be 
damaged.

 

 

 

Summary of Contents for Quantum Flex 1000























































































































Reviews:

No comments