BETTCHER INDUSTRIES Quantum Flex 1000 Operating Instructions/Spare Parts List Download Page 71

Page: 71 / 118

Maintenance

Manual No. 107013

Maintenance

5-33

January 1, 2018

Operating Instructions and Parts List for the Quantum Flex

™

Trimmer

FAULT DETECTION AND CORRECTION

PROBLEM

PROBABLE CAUSE

REMEDY

Handpiece Vibration

Inside bore of handpiece
frame worn out.

Replace frame.

Worn handpiece bearing.

Replace.

Worn pinion gear.

Replace.

Worn teeth on blade or
pinion gear.

Replace.

Blade too loose in blade
housing.

Adjust blade housing. If still too
loose, try a new blade in the
housing.

Blade too tight in the
housing.

Adjust blade housing.

Whizard Quantum

Driveline or Whizard

Flexshaft is worn.

Replace.

Handpiece Hot

Pinion gear tight in hand-
piece bearing.

Clean corrosion from the hand-
piece bearing and lubricate.

Blade tight in blade
housing.

Adjust blade housing.

Handpiece bearing not
installed correctly - (No
clearance between face
of pinion gear and blade
housing) causing
mechanical bind.

Reinstall bearing correctly. With
handpiece removed from
Whizard Quantum

Driveline,

you should be able to rotate the
blade freely by hand.

Rapid Wear

or breakage of the

driveline or flexshaft.

Mechanical bind in hand-
piece.

With handpiece removed from
driveline, blade should rotate
freely by hand. Correct any
mechanical bind.

Drive unit not installed at
proper height or location.

Install drive unit per instructions
in drive unit manual.

Summary of Contents for Quantum Flex 1000























































































































Search results

Summary of Contents for Quantum Flex 1000

Reviews:

Related manuals for Quantum Flex 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Quantum Flex 1000, Operating Instructions/Spare Parts List

Search results

Summary of Contents for Quantum Flex 1000

Reviews:

Related manuals for Quantum Flex 1000

Brands by name

Popular brands