manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex 1000, Operating Instructions/Spare Parts List, Page: 62 / 118

Share
Download
BETTCHER INDUSTRIES Quantum Flex 1000 Operating Instructions/Spare Parts List Download Page 62

Maintenance

5-24

Maintenance

Manual No. 107013

Operating Instructions and Parts List for the Quantum Flex

™

 Trimmer

January 1, 2018

ASSEMBLY OF HANDPIECE (CONTINUED)

Grease Cup and Ring

•

Pick up the Quantum Flex

™

 Trimmer.

•

Pick up the grease cup and ring. Apply a small 

amount of Whizard Quantum

®

 High Performance 

Grease to the frame o-rings.

•

With a twisting motion, install the grease ring onto 

the frame over the o-rings. 

•

Rotate the grease cup to the desired position.

Optional Thumb Support

•

Pick up a spacer ring or optional thumb 

support. 

•

If the optional thumb support is used, align the 

thumb support splines with the frame splines.

•

The optional thumb support should be located 

on the opposite side of the grease cup.

NOTICE

Be careful not to squeeze the 
o-rings out of their grooves, or 
they could be trapped and 
damaged.

GREASE CUP

GREASE RING

FRAME O-RINGS (2)

OPTIONAL THUMB
SUPPORT

FRAME SPLINES FOR

THUMB SUPPORT

THUMB SUPPORT SPLINES

Summary of Contents for Quantum Flex 1000























































































































Reviews:

No comments