manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex 1000, Operating Instructions/Spare Parts List, Page: 35 / 118

Share
Download
BETTCHER INDUSTRIES Quantum Flex 1000 Operating Instructions/Spare Parts List Download Page 35

Instructions for Operation

Manual No. 107013

Instructions for Operation

4-5

January 1, 2018

Operating Instructions and Parts List for the Quantum Flex

™

 Trimmer

STEELING (CONTINUED)

Steeling For Model X750

Be sure to hold the steel at the actual angle of the blade edge. Running the steel at an angle 
greater than the factory ground angle will round over the edge and make resharpening more 
difficult.

Use the steel lightly and always make the last pass of the steel on the blade on the inside surface 
of the blade.

Steeling can be accomplished with much greater consistency with the use of the specially 
designed Whizard

®

 Edge Master Steels. For more information contact your Sales Representative 

at Bettcher Industries. 

Refer to Section 7, Blade Sharpening and Steeling Equipment

.

Replace or sharpen the blade if this procedure does not improve the cutting action. Blade running 
time can be extended with the use of Bettcher

®

 EZ Edge sharpeners. The Bettcher

®

 EZ Edge 

allows the operator to sharpen a blade at the work station. 

Refer to Section 7, Blade Sharpening 

and Steeling Equipment.

The Quantum Flex

™

 Trimmer has been designed in such a way as to allow the blades to be 

quickly removed and reinstalled. 

Refer to Section 4, Blade Changing - Large Tools.

   

 

   

 

Summary of Contents for Quantum Flex 1000























































































































Reviews:

No comments