manualshive.com logo in svg

Berchtold OPERON B 810, Service Parts

Share
Download
Berchtold OPERON B 810 Service Parts Download Page 56

OPERON B 810 SURGICAL TABLE 

PRINCIPLES OF OPERATION

 

Rev. 1 

 

70-000-0027 

4-22 

The charge indicator LED illuminates green when 
AC is applied to the table and the batteries are 

charging.  The indicator should always be illuminated 
if AC is applied. 

Charging LED

Ground Stud

AC Fuse Drawer AC Fuses

Access Cover

For AC Mains

Connection

 

FIGURE 4-36.

 

RIGHT POWER CENTER

CONTROL PENDANTS 
Primary Hand Pendant 

WARNING

 

WARNING – The table has two hand 
pendants that can control its 
movements.  Both can be active at the 
same time.  If different functions are 
pressed on the different hand 
pendants, both functions will activate.  
This could lead to unexpected or 
unintended movement of the table 
sections and could result in injury to 
patients or personnel or in damage to 
the equipment.  To avoid this, keep the 
auxiliary hand pendant securely 
stowed in its drawer during normal 
usage.  When the auxiliary hand 
pendant is deployed during an 
emergency, unplug the primary hand 
pendant to prevent its use. 

Commands are entered on the primary hand pendant 
through the keypad. 

The primary hand pendant sends commands to the 
CPU via connection J6 on the CPU board. 

An illustration of the primary hand pendant along 
with function and LED display descriptions is 
provided in the General Information section of this 
manual. 

If the primary hand pendant is not communicating 
with the CPU, the SERVICE (Service) LED will 
blink. 

If no AC is connected to the table, both the primary 
hand pendant and the table will automatically go into 
sleep mode 2 hours after the last function was 
pressed.  The table may be powered up again by 
pressing any button on the primary hand pendant. 

Pressing ON while a function is running will stop the 
function.  Pressing any other function button while a 

function is running will stop the articulation.  To start 
the articulation, release the function button and press 
it again. 

Pressing OFF while a function is running will stop 
the function and turn the table off. 

If AC is connected to the table, the auto-shutdown 
feature is disabled (i.e., the hand pendant and table 
operations will not automatically turn off after 2 
hours of non activity). 

The auxiliary hand pendant drawer does not have an 
affect on the primary hand pendant’s power.  
Removing the auxiliary pendant activates the 
auxiliary pendant, but it does not deactivate the 
primary hand pendant.  Thus, if a function is pressed 
on the primary pendant while another function is 
pressed on the auxiliary pendant, both valves will 
open and pump pressure will activate both 
movements. 

There are no field serviceable parts in the primary 
hand pendant.  It must be replaced as a complete 
assembly. 

Summary of Contents for OPERON B 810

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands