manualshive.com logo in svg

BendPak HD-7500 Series, Installation And Operation Manual

The BendPak HD-7500 Series is a top-of-the-line automotive hoist designed for heavy-duty use. Ensure a safe installation and smooth operation with the comprehensive Installation and Operation Manual. Easily downloaded for free from our website, manualshive.com, this essential manual provides valuable instructions and guidelines for optimal machine performance.

Share
Download
background image

 

Manual.

 HD-7500 Four-Post Lift series, 

Installation and Operation Manual

, Manual P/N 5900174, Manual 

Revision C, Released March 2021. 

Copyright.

 Copyright © 2021 by BendPak Inc. All rights reserved. You may make copies of this document if you 

agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain 

any rights to this content, and you will not use the copies for commercial purposes. 

Trademarks.

 BendPak and the BendPak logo are registered trademarks of BendPak Inc. All other company, 

product, and service names are used for identification only. All trademarks and registered trademarks mentioned 
in this manual are the property of their respective owners. 

Limitations.

 Every effort has been made to make sure complete and accurate instructions are included in this 

manual. However, product updates, revisions, and/or changes may have occurred since this manual was 

published. BendPak reserves the right to change any information in this manual without incurring any obligation for 

equipment previously or subsequently sold. BendPak is not responsible for typographical errors in this manual. 
You can always find the latest version of the 

manual for your product on the BendPak website

. 

Warranty.

 The BendPak warranty is more than a commitment to you: it is also a commitment to the value of 

your new product. Contact your nearest BendPak dealer or visit 

www.bendpak.com/support/warranty

 for 

full warranty details. Go to 

bendpak.com/support/register-your-product/

 and fill out the online form to 

register your product (be sure to click 

Submit

).

 

Safety.

 Your product was designed and manufactured with safety in mind. However, your safety also depends 

on proper training and thoughtful operation. Do not install, operate, maintain, or repair the unit without reading and 

understanding this manual and the labels on the unit; 

do not use your Lift unless you can do so safely!

 

Owner Responsibility.

 In order to maintain your product properly and to ensure everyone’s safety, it is the 

responsibility of the product owner to read and follow these instructions: 

•  Follow all installation, operation, and maintenance instructions. 
•  Make sure product installation conforms to all applicable local, state, and federal codes, rules, and regulations, 

such as state and federal OSHA regulations and electrical codes. 

•  Read and follow all safety instructions; keep them readily available for operators. 

•  Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised. 
•  Do not operate the product until you are certain that all parts are in place and operating correctly. 

•  Carefully inspect the product on a regular basis and perform all maintenance as specified. 

•  Service and maintain the unit with approved replacement parts only. 

•  Keep instructions permanently with the product  

and make sure all labels are clean and visible. 

• 

Only use the Lift if it can be used safely!

 

 
Unit Information.

 Enter the Model Number, Serial 

Number, and the Date of Manufacture from the label 
on your unit. This information is required for part or 

warranty issues. 

 

Model:  

 

 

Serial:  

 

 

Date of Manufacture:  

 

 

 

 

Summary of Contents for HD-7500 Series





















































































Reviews:

No comments

Related manuals for HD-7500 Series

IN-COMMAND NCSP35CM Installation And Operation Manual preview
NCSP35CM
Brand: IN-COMMAND Pages: 47
STAYER WELDING MAG Series Operating Instructions Manual preview
MAG Series
Brand: STAYER WELDING Pages: 56
Barton RCL-4002 Operation Manual preview
RCL-4002
Brand: Barton Pages: 36
GSK 983Ma-H Connection Manual preview
983Ma-H
Brand: GSK Pages: 32
Paton Cooler-7 User Manual preview
Cooler-7
Brand: Paton Pages: 17
Riello 20116460 Instruction Booklet preview
20116460
Brand: Riello Pages: 2
CTE ZED 20.3 HV Instructions For Use And Maintenance Manual preview
ZED 20.3 HV
Brand: CTE Pages: 130
ESAB 0904 200 880 Instruction Manual preview
0904 200 880
Brand: ESAB Pages: 44
Thermal Arc 161 S Operating Manual preview
161 S
Brand: Thermal Arc Pages: 56
JLG LiftPod FS60 Operation, Safety, Service And Maintenance Manual preview
LiftPod FS60
Brand: JLG Pages: 97
Telwin PLASMA 30 Instruction Manual preview
PLASMA 30
Brand: Telwin Pages: 56
M-system R3-SV8 Instruction Manual preview
R3-SV8
Brand: M-system Pages: 3
Riello RK Hydroline N Installation Instructions Manual preview
RK Hydroline N
Brand: Riello Pages: 20
gala gar GALA MIG 410 Technical Instruction Manual preview
GALA MIG 410
Brand: gala gar Pages: 33
Fronius AL 2300 Operating Instructions Manual preview
AL 2300
Brand: Fronius Pages: 92
National Instruments PXI-6040E User Manual preview
PXI-6040E
Brand: National Instruments Pages: 265
pewag BLCW Owner'S Manual preview
BLCW
Brand: pewag Pages: 24
Abicor Binzel TIG ABITIG MT Operating Instructions Manual preview
TIG ABITIG MT
Brand: Abicor Binzel Pages: 100

Brands by name

Popular brands

Load more brands