BendPak HD-7500 Series Installation And Operation Manual Download Page 57

Page: 57 / 84

HD-7500 Series Four-Post Lifts

P/N 5900174 — Rev. C — March 2021

Tire Stops

Tire Stops are attached on the Front of the Lift. They prevent the tires of the Vehicle on the Lift from

going too far forward.

To install the Tire Stops

Locate the two Tire Stops, two Tire Stop Pins, and four Rotor Clips.

Put one Tire Stop in position between the Tubes attached to the Runway, then put the Tire Stop

Pin all the way through the Tire Stop and the Tubes.

Secure the Tire Stop with Rotor Clips on each end of the Tire Stop Pin.

Repeat Steps 2 and 3 for the second Tire Stop.

Ramps

Your Lift comes with two steel Ramps, for driving Vehicles onto the Runways.

To install the Ramps

Find the required components: two Ramps, two Ramp Pins, and four Rotor Clips.

Put a Ramp into position on the end of a Runway at the Rear of the Lift, with the Tube on the

bottom of the Ramp between the two Tubes on the end of the Runway.

Slide a Ramp Pin through the three Tubes, then install Rotor Clips on both ends of the Ramp Pin.

Note

: The Ramps are heavy and awkward, so you may want to consider having two people

install them; one to hold the Ramp, the other to put the components into place.

Repeat Steps 2 and 3 for the other Ramp.

Summary of Contents for HD-7500 Series




















































































Search results

Summary of Contents for HD-7500 Series

Reviews:

Related manuals for HD-7500 Series

Brands by name

Popular brands

BendPak HD-7500 Series, Installation And Operation Manual

Search results

Summary of Contents for HD-7500 Series

Reviews:

Related manuals for HD-7500 Series

Brands by name

Popular brands