BendPak HD-7500 Series Installation And Operation Manual Download Page 14

Page: 14 / 84

HD-7500 Series Four-Post Lifts

P/N 5900174 — Rev. C — March 2021

Selecting a Power Post Location

You need to pick a Power Post location now, near the beginning of the installation process, as its

location impacts other aspects of the installation.
You have two options for Power Post location:

Driver-Side Front

Passenger-Side Rear

Note

: The Power Post location decision has no impact on the Approach direction or where the

Front and Rear of the Lift are. It does impact other aspects of the installation, however.

Drawing not necessarily to scale. Not all components shown. Powerside Runway (which has the
Hydraulic Cylinder under it)

must

be installed next to the Power Post, no matter which Power Post

location you choose.

Most customers choose their Power Post location based on either preference (one option makes more

sense for their shop than the other does) or easier access to the power source.

Summary of Contents for HD-7500 Series




















































































Search results

Summary of Contents for HD-7500 Series

Reviews:

Related manuals for HD-7500 Series

Brands by name

Popular brands

BendPak HD-7500 Series, Installation And Operation Manual

Search results

Summary of Contents for HD-7500 Series

Reviews:

Related manuals for HD-7500 Series

Brands by name

Popular brands