BendPak HD-7500 Series Installation And Operation Manual Download Page 5

Page: 5 / 84

HD-7500 Series Four-Post Lifts

P/N 5900174 — Rev. C — March 2021

•

BendPak recommends making a

thorough

inspection of the product at least once a year.

Replace any damaged or severely worn parts, decals, or warning labels.

Symbols

Following are the symbols used in this manual:

⚠

DANGER

Calls attention to an immediate hazard that

will

result in death or severe injury.

⚠

WARNING

Calls attention to a hazard or unsafe practice that

could

result in death or severe

personal injury.

⚠

CAUTION

Calls attention to a hazard or unsafe practice that could result in minor personal
injury, product damage, or property damage.

NOTICE

Calls attention to a situation that, if not avoided, could result in product or property
damage.

Tip

Calls attention to information that can help you use your product better.

Liability Information

BendPak Inc. assumes

liability for damages resulting from:

• Use of the equipment for purposes other than those described in this manual.
• Modifications to the equipment without prior, written permission from BendPak.
•

Injury or death caused by modifying, disabling, overriding, or removing safety features.

• Damage to the equipment from external influences.
• Incorrect operation of the equipment.

Electrical Information

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician. Do not perform

any maintenance until main electrical power has been disconnected from the Lift
and cannot be re-energized until all procedures are complete.

Important electrical information:
•

Improper electrical installation can damage the Power Unit motor, which is not covered by the

warranty.

•

The Lift uses electrical energy; if your organization has Lockout/Tagout policies, make sure to

implement them after connecting to a power source.

•

Use a separate circuit breaker for each Power Unit.

•

Protect each circuit with a time delay fuse or circuit breaker:
–

For a 208 to 230 VAC,

single phase

circuit, use a 25 amp fuse.

–

For a 208 to 230 VAC,

three phase

circuit, use a 20 amp fuse.

Summary of Contents for HD-7500 Series




















































































Search results

Summary of Contents for HD-7500 Series

Reviews:

Related manuals for HD-7500 Series

Brands by name

Popular brands

BendPak HD-7500 Series, Installation And Operation Manual

Search results

Summary of Contents for HD-7500 Series

Reviews:

Related manuals for HD-7500 Series

Brands by name

Popular brands