BendPak HD-7500 Series Installation And Operation Manual Download Page 37

Page: 37 / 84

HD-7500 Series Four-Post Lifts

P/N 5900174 — Rev. C — March 2021

Installing the Power Unit

This section describes how to

install

, but not make the connections to, the Power Unit for your Lift.

An Electrician is

not

needed to

install

the Power Unit; however, an Electrician

required to

connect

the Power Unit to its power source.
The Power Unit

must

be installed on the Power Post: attach it to one of the two Mounting Brackets,

whichever is more convenient for the location.

Important

Many people install the Flex Tube Bracket Plate and/or the Zero Angle Bracket at the
same time as they install the Power Unit. Read

Installing the Second End of the

Flex Tube

and

Installing the Pushbutton Air Valve

for more information to see

if this makes sense for your installation.

⚠

DANGER

Risk of explosion: The Power Unit has internal arcing or parts that may spark and
should not be exposed to flammable vapors. Never expose the Power Unit motor
to rain or other damp environments. Damage to the motor caused by water is

not

covered by the warranty.

Tip

The Power Unit is heavy. BendPak recommends having one person hold the Power Unit
while another person bolts it into place.

To install the Power Unit

Find the four supplied Hex Head Bolts, Flat Washers, Nyloc Nuts, and the Vibration Dampener.

Line up the holes on the Vibration Dampener with the four holes in the Mounting Bracket.

If you are going to install the Flex Tube Bracket Plate and/or the Zero Angle Bracket at the same

time as the Power Unit, now is the time to put them into place.

Put a Flat Washer onto each of the four Hex Head Bolts, slide the Bolts through the back of the

Mounting Bracket and through the holes in the Vibration Dampener, then put on the Nyloc Nuts to

secure the Power Unit in place.

Summary of Contents for HD-7500 Series




















































































Search results

Summary of Contents for HD-7500 Series

Reviews:

Related manuals for HD-7500 Series

Brands by name

Popular brands

BendPak HD-7500 Series, Installation And Operation Manual

Search results

Summary of Contents for HD-7500 Series

Reviews:

Related manuals for HD-7500 Series

Brands by name

Popular brands