BendPak HD-7500 Series Installation And Operation Manual Download Page 44 | Manualshive

Page: 44 / 84

background image

HD-7500 Series Four-Post Lifts

44

P/N 5900174 — Rev. C — March 2021

The components involved include:
•

Zero Angle Bracket

. Attaches at the Mounting Bracket on the Power Post or to other available

holes on the Back Plate of the Power Unit. Holds the Pushbutton Air Valve, so be sure to orient the

Zero Angle Bracket so that the Pushbutton Air Valve can be easily reached by the Lift operator.

•

Pushbutton Air Valve

. Used to lower the Runways.

•

Air Line Compression Elbow Fitting

. Connects the Pushbutton Air Valve to the Air Line

coming out of the Flex Tube.

•

Straight Expander Fitting

. Connects the Pushbutton Air Valve to the customer-supplied air

pressure.

To install the Pushbutton Air Valve:

1.

Find the necessary components: Zero Angle Bracket, Pushbutton Air Valve, Air Line Compression
Elbow Fitting, and Straight Expander Fitting.

2.

Connect the Zero Angle Bracket at the desired location (if it has not already been connected).
It can attach to an available hole on the Back Plate of the Power Unit or to one of the Bolts that
connect the Power Unit to the Mounting Bracket on the Power Post.

3.

Connect the Pushbutton Air Valve to the Zero Angle Bracket.
Use the two holes on the Pushbutton Air Valve on the side away from the actual pushbutton. If

you use the holes next to the pushbutton, the Zero Angle Bracket interferes with the pushbutton
when you try to use it.

4.

Connect the Air Line Compression Elbow Fitting and the Straight Expander Fitting to the

appropriate locations on the Pushbutton Air Valve.
The elbow fitting connects to the opening labelled

CYL

. The straight fitting to the opening labelled

IN

. See the drawing above.

5.

Attach the Air Line (coming out of the Flex Tube) to the compression fitting on the elbow fitting
and the customer-supplied air to the straight fitting.

Important

: The Return Line also comes out of the Flex Tube and is the same kind of tubing as the

Air Line.

Do not attach the Return Line to the Pushbutton Air Valve by

mistake

. Double check to make sure you are attaching the Air Line to the Pushbutton

Air Valve.

«
...
42
43
44
45
46
...
»

Summary of Contents for HD-7500 Series





















































































Reviews:

No comments

Related manuals for HD-7500 Series

Brand: Union Instruments Pages: 63

Brand: VENCO Pages: 44

Brand: Wabtec Pages: 106

EcoTouch Ai1 Geo

Brand: WATERKOTTE Pages: 60

Brand: WaterCop Pages: 4

Brand: Jasic Pages: 20

TLX-7000-FLRAILKIT

Brand: IDEAL Pages: 10

Brand: Vestil Pages: 8

SAF-FRO PRESTOTIG 240 AC/DC

Brand: Air Liquide Pages: 121

Brand: Madas Pages: 58

AeGIS 9100CR200

Brand: PACH & COMPANY Pages: 49

SystemRoMedic SlingBarSpreader M

Brand: Handicare Pages: 3

NOVOLAS Basic AT

Brand: Leister Pages: 62

IDEALARC CV-250

Brand: Lincoln Electric Pages: 42

Brand: R. Beck Maschinenbau Pages: 40

Brand: Infinity Pages: 24

Brand: B-TEC Pages: 33

Brand: EWM Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands