manualshive.com logo in svg

BC Biomedical DA-2006, Service Manual, Page: 78 / 171

Share
Download
BC Biomedical DA-2006 Service Manual Download Page 78

 

 

71

 

 

The DA-2006P can display a graphical representation of the last pulse.  This screen may 

be accessed by pressing the          key from the PACE MAIN SCREEN.  The 

playback allows the user to view the Pacemaker pulse in a time-expanded form.  Samples 

are stored internally at 0.1 ms intervals.  The PLAYBACK LAST PULSE SCREEN shows 

these samples expanded by a time factor of 200.  

 

In playback mode, the samples are shown on the display and sent out the ECG leads, 

Defibrillator Plates, and the High Level output.  The following is a sample of the waveform 

that is shown in the display: 

 
 
 
 
 
 
 
The scale shown on the screen is automatically adjusted to provide the maximum 

resolution available.   

 

The                       key can be used to pause the screen at any point while a pulse is being 

played back.  This key replaces the                      key when a pulse is being played back. 

 

The                       key can be used to play (continue) the waveform if it has been paused.  

This key replaces the                      key. 

PLAYBACK LAST PULSE SCREEN 

 

 

 

 

 

 

Summary of Contents for DA-2006












































































































































































Reviews:

No comments