manualshive.com logo in svg

BC Biomedical DA-2006, Service Manual, Page: 105 / 171

Share
Download
BC Biomedical DA-2006 Service Manual Download Page 105

Programming Auto Sequences 

 

98

 

FILE CONTROL

 

The file control section allows the user to Load and Save Auto Sequence files, greatly 

expanding the number of pre-programmed sequences from 50 to virtually unlimited.  The 

user also uses the File Control section to Load and Store Auto Sequences on the 

DA-2006/P.   

 

 

 

 

Dropdown List

 – This list shows the history of files that have recently been used.  This 

provides quick access for switching between common Auto Sequence files.   

 

Open Auto Sequence File

 – This button brings up the standard Windows Open File dialog 

box.  It is used to load an existing configuration file. 

 

Save Auto Sequence to File

 – This button brings up the standard Windows Save File 

dialog box.  It is used to save the current configuration to a file for future reference.   

 

Read Auto Sequence from DA-2006/P

 – This button is used to load the configuration 

currently stored in the DA-2006/P.   

 

Download Auto Sequence to DA-2006/P

 – This button is used to send the configured 

Auto Sequence to the DA-2006/P, where it is stored in non-volatile flash memory.   

Summary of Contents for DA-2006












































































































































































Reviews:

No comments