manualshive.com logo in svg

BC Biomedical DA-2006, Service Manual, Page: 146 / 171

Share
Download
BC Biomedical DA-2006 Service Manual Download Page 146

 

B 7

OSCILLOSCOPE OUTPUT 

The oscilloscope output is driven from multiplexer U8.  The signals routed to the multiplexer 

are the same signals that are routed to the A/D converter.  U7 provides buffering and 

filtering for the oscilloscope output.  The microprocessor selects either the Defibrillator or 

Pacemaker signals based on the operating mode of the DA-2006P.   

 

ECG OUTPUT 

The ECG output consists of a D/A converter with a variable reference voltage.  The 

reference voltage is generated by the microprocessor and buffered by U2:A.  The reference 

voltage is used to select the ECG Output amplitude.  The ECG output waveform is 

generated by the D/A converter U3.  The output of the D/A converter is buffered and scaled 

by U2:B and U2C for the ECG output and U2:D for the High Level output.  It is also routed 

to the Defibrillator Output amplifier U4:A and the Pacemaker output attenuator U9.  The 

ECG signal is routed to the ECG distribution board via J1.  The distribution board contains 

all of the resistive dividers used to generate the individual output voltages.   

 

.

Summary of Contents for DA-2006












































































































































































Reviews:

No comments