BC Biomedical DA-2006 Service Manual Download Page 72

Page: 72 / 171

The Sensitivity Test is used to determine the smallest waveform that the pacemaker can

detect. For this test, the selected waveform is generated outside of the refractory period of

the pacemaker. The DA-2006P uses a successive approximation approach to determine

the smallest output waveform that can be detected by the pacemaker. The Sensitivity Test

may be initiated by pressing the key from the PACE MAIN SCREEN.

While this test is running, the following display will show the progress of the test:

At any time, the key can be depressed to stop the test and return to the

PACE MAIN SCREEN.

SENSITIVITY TEST

WARNING

This section is provided as a guide to familiarize

the user with the DA-2006P. It is not intended to

provide the necessary test sequence for every

Pacemaker. The user must consult the

manufacturer’s manual for each DUT to

determine the correct test procedure to follow.

Summary of Contents for DA-2006












































































































































































Search results

Summary of Contents for DA-2006

Reviews:

BC Biomedical DA-2006, Service Manual, Page: 72 / 171

Search results

Summary of Contents for DA-2006

Reviews: