BC Biomedical DA-2006 Service Manual Download Page 153

Page: 153 / 171

C 7

The Calibration procedure is used to adjust the UUT to comply with manufacturers

specifications. This procedure should only be performed if the UUT failed the

Defibrillator Input, Pacemaker Load Resistance or Pacemaker Input Verification tests.

After calibration is performed, the Verification test should be run to validate the new

calibration settings.

Part of the calibration can be performed Closed Box, other parts require Open Box. Closed

Box refers to the digital calibration adjustments that do not require the technician to open

the UUT.

NOTE: Opening the UUT will void the Manufacturer’s Warranty. Not all calibration

adjustments can be made Closed Box.

REQUIRED EQUIPMENT

The following equipment is needed for Validation / Calibration:

DMM, Fluke 45 or Equivalent

Battery Eliminator, 10VDC, 300mA, Regulated

Adjustable Power Supply, 0-12VDC, 500mA

Defibrillator (With pacemaker function for DA-2006P)

BC Biomedical Defibrillator Analyzer Calibration Interface Module (DA-CS-06)

PC Running the Calibration Interface Module software (DA-CS-06)

Oscilloscope, Lecroy 9304AM or equivalent

Centronics printer (DeskJet or Dot-Matrix)

CALIBRATION

Summary of Contents for DA-2006












































































































































































Search results

Summary of Contents for DA-2006

Reviews:

BC Biomedical DA-2006, Service Manual, Page: 153 / 171

Search results

Summary of Contents for DA-2006

Reviews: