Baumuller BUS 6 VC Manual Download Page 77

Page: 77 / 110

Parameter

V-Controller (BUS 6 VC)

Baumüller Nürnberg Electronic GmbH & Co. KG

5.03047.01

P279

1 scaling

P286

2 scaling

These parameters enable scaling of the analog input variable.

The output values (see parameters P283, P290, P297, P304) of unsigned parameters are 0

till +100 % and of signed parameters are -100 % till +100 %. Which analog input voltage this

maximum values achieved depends on the scaling factor.

P280

1 target Pxxx

P287

2 target Pxxx

The receiver address for the output value can be set via this parameter.

P281

1 offset

P288

2 offset

These parameters can compensate for a possibly existing input voltage offset.

P282

1 threshold value

P289

2 threshold value

The sensitivity of the inputs can be set via the threshold values.

P283

1 value

P290

2 value

The AI value displays the respective current output value taking scaling and offset compen-

sation into consideration.

NOTE

No target parameter number check is carried out.

Summary of Contents for BUS 6 VC















































































































Search results

Summary of Contents for BUS 6 VC

Reviews:

Related manuals for BUS 6 VC

Brands by name

Popular brands

Baumuller BUS 6 VC, Manual

Search results

Summary of Contents for BUS 6 VC

Reviews:

Related manuals for BUS 6 VC

Brands by name

Popular brands