Barco R9841020 Cine VERSUM Master, Installation Manual

Page: 87 / 161

12. Image Projection after Powering Up
12.3.2 Lamp Mode Set Up Economic/Normal (Image Settings menu)
How to set up:
1. Enter the MAIN menu and scroll through the sub menus, using the jog dial or the Remote Control until the Image Settings menu
is displayed. (image 12-2)
2. Select menu item
LAMP POWER
and enter the lamp mode ’Economic’ or ’Normal’ by pressing the jog dial or the ENTER key on
the Remote Control.
Note: To increase the lamp life time, enter the economic lamp power mode.
3. Leaving the GUI, use the
BACK
item in the menu or press EXIT key on the Remote Control.
CineVERSUM
Image settings
Advanced Settings
Installation
Service
1 NO MODULE
2 NO MODULE
3 VIDEO [VIDEO]
4 NO MODULE
5 NO MODULE
6 NO MODULE
7 RGB-YUV [RGB]
8 NO MODULE
Shut Down
Back
Image Settings
Master
Brightness
Contrast
Saturation
Tint
Display
Back
Display List
1 CV50 On
2 CV80 On
3 CV120 On
Back
[Economic/Normal]
Cine VERSUM r01
CV120
Main Menu/
Image Settings
/
Display
/
CV80 or CV120
/
Lamp Power
If the CV120 is the only display in the link
Image Settings
Display
Brightness
Contrast
Gamma
Color Temperature
Primaries: [Projector]
Lamp mode:[Single]
Lamp Power: [Normal]
Master
Back
Image 12-2
Menu item Lamp Power
12.3.3 Lamp mode/Power set up in Display Settings menu
How to set up
1. Enter the MAIN menu and scroll through the sub menus, using the jog dial or the Remote Control until the Display Settings menu
for the Cine VERSUM 120 is displayed. (image 12-3)
2. Select item
LAMP
and press jog dial or ENTER key to confirm.
Lamp menu is displayed, inclusive items
MODE
and
POWER
.
3. To set up Lamp Power, select item
POWER
and press the jog dial or the ENTER key on the remote Control for ’Normal’ or
’Economic’ lamp power.
4. To set up the Lamp Mode, select item
MODES
and press the jog dial or the ENTER key on the remote Control.
A lamp mode menu is displayed allowing 4 different possibilities. The active mode is preceded with a star. Select the mode you
desire and press the jog dial or
ENTER key on the Remote Control to confirm.
- DUAL: both lamps will be ignited at start up (Can be overruled in the IMAGE SETTINGS menu).
- LEAST USED (=SINGLE): least used lamp of both will be ignited at start up (Can be overruled in the IMAGE SETTINGS
menu).
- LAMP 1: at start up, Lamp 1 will be forced to ignite (CANNOT be overruled in the IMAGE SETTINGS menu).
- LAMP 2: at start up, Lamp 2 will be forced to ignite (CANNOT be overruled in the IMAGE SETTINGS menu).
5. Leaving the GUI, use the
BACK
item in the menu or press EXIT key on the Remote Control.
Cine VERSUM r01
Lamp
Modes: [Dual]
Power: [normal]
Max run time
Lamp 1
Run time: 50
Nr Strikes: 20
Last power: 200W
Lamp 2
Run time: 40
Nr Strikes: 10
Last power: 250W
Back
Lamp Mode
*Dual
Least used
Lamp 1
Lamp 2
Back
[Normal/Economic]
Main Menu/
Installation
/
Display List
/
CV120
/
Lamp
Display Settings
Switch OFF
Display Info
Rename
IR Address 009
Diagnosis
Orientation
Test patterns
Lens
Lamp
Back
Display List
1 CV50 On
2 CV80 On
3 CV120 On
Back
Installation
Input Slots
File Service
Display List
Internal Pattern
When no signal
Source Transition
OSD configuration
Language
Keystone
Global Keystone:Yes
Output: [Largest]
Default Input Balance
Back
Image 12-3
Menu item lamp
R5976468 CINE VERSUM SYSTEM 03112003 83