Barco DP-1200 Installation Manual Download Page 41 | Manualshive

Page: 41 / 134

background image

4. Lamp & Lamp House

L

N2

S

W1

W2

N1

N1

N2

9 Nm

Image 4-13

5. Remove the protective container or unwrap the protective cloth from the xenon bulb lamp.

Warning:

Ensure that you wear protective clothing, a full face shield and protective gloves.

Tip:

Write down the serial number of the lamp. You will need this while updating the lamp parameters after installation of the
lamp. The serial number of the lamp is engraved in the neck of the xenon bulb lamp.

6. Gently guide the xenon bulb lamp into position inside the lamp house as illustrated. Anode socket hanging vertical down. While

inserting the lamp, rotate it slightly, engaging the pins of the cathode adapter in the foreseen slots. This is to ensure the lamp
cathode is completely inserted.

Warning:

Make sure that the both pins of the cathode adapter are engaged in the foreseen slots.

Image 4-14

7. Insert the anode socket into position as illustrated.

Caution:

Avoid any tension on the anode wire, so there is no mechanical stress on the bulb of the lamp.

R59770242 DP-1200 06/01/2009

37

«
...
39
40
41
42
43
...
»

Summary of Contents for DP-1200







































































































































Reviews:

No comments

Related manuals for DP-1200

Brand: CAPTELEC Pages: 10

Brand: Projectiondesign Pages: 86

Brand: ProLights Pages: 36

Brand: Intermatic Pages: 2

Brand: Radiola Pages: 48

CP-X1200 Series

Brand: Hitachi Pages: 78

CP-X10000 Series

Brand: Hitachi Pages: 3

Brand: Hitachi Pages: 4

Brand: Hitachi Pages: 1

Brand: Hitachi Pages: 170

Brand: Hitachi Pages: 35

Brand: Hitachi Pages: 1

Brand: Hitachi Pages: 1

Brand: SKYTRONIC Pages: 20

Wall tap SPP2303WC

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Xtreme Surge Protector I

Brand: Philips Pages: 12

Theatre Director SPP4200

Brand: Philips Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands