Barco DP-1200 Installation Manual Download Page 106

Page: 106 / 134

11. Maintenance

11.1 Replacement of the dust

lter on the front side

The front

lter of the projector can be removed from the lamp side of the projector in case there is insuf

cient place at the front of the projector or in case you want to avoid the removal of the lens. This procedure
describes how to access the front

lter from the side of the projector.

Necessary parts

New dust

lter for the front side.

How to replace the HEPA dust

lter on the front side of the projector?

1. Remove the input cover of the projector.

2. Release the captive screw of the front cover and pull the left side of the front cover 5 centimeters away from the projector. No

need to remove the front cover.

3. Turn the three latches of the front

lter compartment 90° counterclockwise.

Image 11-1

4. Pull out the front dust

lter as illustrated.

102

R59770242 DP-1200 06/01/2009

Summary of Contents for DP-1200







































































































































Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands

Barco DP-1200, Installation Manual

Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands