Barco DP-1200 Installation Manual Download Page 118

Page: 118 / 134

12. Convergence (with extenders)

Image 12-7

4. Slightly turn the red colored control knob number 3 until the red pattern in the upper right of the projected image converges with

the blue pattern.

Image 12-8

5. Repeat step 3 and 4 until coincidence is obtained of the red pattern in the lower left and upper right of the projected image.

6. Repeat from step 2 until full coincidence is obtained of the red pattern in the center, lower left and upper right of the projected

image.

7. Carefully secure the position of the DMD assembly by tightening the four convergence lock screws (reference 7 of image 12-5)

of the red channel. Fasten the screws crosswise and with small adjustments to each screw. Use a torque wrench with a 2,5 mm
Allen socket and a torque of

0,6 Nm

(0,44 lbf*ft).

114

R59770242 DP-1200 06/01/2009

Summary of Contents for DP-1200







































































































































Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands

Barco DP-1200, Installation Manual

Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands