Barco DP-1200 Installation Manual Download Page 52

Page: 52 / 134

5. Lenses & lens holder

5.3

Lens formulas

Formulas

Lens

Throw ratio for 0.98" DC2K Zoom

Formulas (metric and inches)

0.98” DC2K Zoom (1.2–1.81:1)

1.2 - 1.81

min

=1.2 x SW

max

=1.81 x SW

0.98” DC2K Zoom (1.4–2.05:1)

1.4 - 2.05

min

=1.4 x SW

max

=2.05 x SW

0.98” DC2K Zoom (1.6–2.5:1)

1.6 - 2.5

min

=1.60 x SW

max

=2.50 x SW

0.98” DC2K Zoom (1.95–3.2:1)

1.95 - 3.2

min

=1.95 x SW

max

=3.2 x SW

0.98” DC2K Zoom (2.4–3.9:1)

2.4 - 3.9

min

=2.4 x SW

max

=3.9 x SW

Due to production tolerances the real distances can differ by 2% from these calculated values.

For critical situations (

xed installs that use the lens at one of its extreme zoom positions) this should be

taken into account.

AUTION

Never transport the projector with a lens mounted in the lens holder. Always remove the lens

before transporting the projector. Neglecting this can damage the lens holder and prism.

R59770242 DP-1200 06/01/2009

Summary of Contents for DP-1200







































































































































Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands

Barco DP-1200, Installation Manual

Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands