Barco DP-1200 Installation Manual Download Page 116

Page: 116 / 134

12. Convergence (with extenders)

12.2 Preparing for convergence adjustment

Necessary tools

Flat blade screwdriver 7x150.

How to set up the projector for convergence adjustment?

1. Remove all side covers and top cover of the projector. See "Removal and installation of projector covers", page 85. Note that all

side covers have to be removed before you can remove the top cover.

2. Open the sealed compartment of the Light Processor. See "Open the sealed compartment", page 92.

3. Remove the convergence cover plate in the top plate as follow:

a) loosen both captive screws (reference 1).
b) slide the cover plate forward until it becomes free from the top plate.
c) take off the cover plate.

Image 12-3

4. Reinstall the lens and start up the projector.

5. Use the Communicator software to activate the convergence test pattern.

Image 12-4

112

R59770242 DP-1200 06/01/2009

Summary of Contents for DP-1200







































































































































Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands

Barco DP-1200, Installation Manual

Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands