Barco DP-1200 Installation Manual Download Page 44

Page: 44 / 134

4. Lamp & Lamp House

4.5

Installation of the lamp house

ARNING

This procedure may only be performed by quali

ed technical service personnel.

AUTION

Due to its high internal pressure, the lamp may explode in either hot or cold states if improperly

handled.

Necessary tools

7 mm

at screw driver.

How to install the lamp house of the projector ?

1. Ensure the projector is switched off.

2. Remove the lamp cover.

3. Hold fast the lamp house by its handles and gently slide the lamp house into its socket. Note that the compartment is provided

with guides (G) to position the lamp house correctly.

Image 4-20

4. Push the lamp house forward until it slides fully into the projector.

5. Secure the correct position of the lamp house by tightening all three spring lock screws as illustrated.

Image 4-21

6. Reinstall the lamp cover of the projector.

R59770242 DP-1200 06/01/2009

Summary of Contents for DP-1200







































































































































Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands

Barco DP-1200, Installation Manual

Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands