Barco DP-1200 Installation Manual Download Page 72

Page: 72 / 134

7. Communicator touch panel

7.2

Installing the touch panel interface

Necessary tools

•

17 mm wrench.

•

10 mm wrench.

How to install the touch panel interface upon the DP-1200 projector?

1. Assemble the mounting plate and the swivel arm together as illustrated. First the nut (N) upon the rod of the mounting plate, then

the lock washer (L), and then fasten mounting plate and swivel arm together. When arm is mounted, turn nut (N) against the arm
to secure the position.

Image 7-3

2. Slide a washer (M) over the base of the swivel arm and Insert the base of the swivel arm into the mounting hole at the top of the

DP-1200 projector as illustrated.

Image 7-4

3. Place the touch panel interface upon the mounting plate of the swivel arm and fasten the two wing nuts (W) as illustrated.

Image 7-5

4. Connect the circular plug of the multi cable with the circular socket at the rear side of the DP-1200 projector.

R59770242 DP-1200 06/01/2009

Summary of Contents for DP-1200







































































































































Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands

Barco DP-1200, Installation Manual

Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands