Barco DP-1200 Installation Manual Download Page 26

Page: 26 / 134

3. Physical Installation

3.3

Connecting the projector with the power net

ARNING

The total electrical installation should be protected by an appropriate rated and readily accessi-

ble disconnect switch, circuit breakers and ground fault current interrupters. The installation shall be done
according to the local electrical installation codes.

AUTION

ALL POWER CONNECTIONS to the DP-1200 projector are made to the three-terminal strip located

in a sealed compartment behind the rear cover of the projector.

AUTION

The cross-sectional area of the conductors in the Power Supply Cord shall be not less than 4 mm

or AWG 10

Necessary tools

•

Flat screw driver.

•

Phillips screw driver PH2.

Necessary parts

•

Two cable ties.

•

Certi

ed AC power supply cord 4.0 mm², 10AWG, min. 300V.

How to connect the main AC power with the DP-1200 projector?

1. Remove the rear cover and lamp cover of the projector.

2. Remove the cover of the main AC compartment by releasing the three captive dumb screws.

Image 3-6

3. Guide the AC power cord through the cable gland and connect the wires to the 3-terminal strip as illustrated.

Warning:

Always connect

rst the PE wire.

Image 3-7

R59770242 DP-1200 06/01/2009

Summary of Contents for DP-1200







































































































































Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands

Barco DP-1200, Installation Manual

Search results

Summary of Contents for DP-1200

Reviews:

Related manuals for DP-1200

Brands by name

Popular brands