13
block the wheels.
(40) When tilting the mast forward or backward to the limit or lifting the fork to the
maximum height, return the directional lever to neutral.
(41) Don’t adjust the control valve and relief valve at will to pr
event the damage of
hydraulic system and its components because of excessive pressure passing them.
(42) Tyres should be inflated according to the pressure valve specified in the marking
plate of “
Tyre
Pressure”.
(43) According to the Directive 2000/14/EC and based on EN12053 standard
,
when
the forklift truck during the test of lifting, traveling and idling, but the noise of the forklift
truck may
due to different operation and the influence of the external
environment.
(44) The driver feels the vibration of the forklift truck when operating and traveling the
forklift truck. According to ISO3691 and based on EN 13059 standard. The vibration of the
forklift truck fluctuates according to environment condition. In normal working condition,
the vertical direction acceleration mean value from the seat to the operator is referred to
the following table. But the vibration frequency felt by the driver depends on the working
condition (etc. road, operation method), so the actual vibration frequency must be
determined according to environment condition when necessary.
Model
The noise pressure level at
the operato
r’s position
The vertical direction acceleration mean
value from the seat to the operator
EN 12053
EN 13059
CPD10-15
69.1dB(A)
1.10(m/s
2
)
CPD20-25
78.3dB(A)
1.08(m/s
2
)
CPD30
63.9dB(A)
1.11(m/s
2
)
(45) Users select “Lengthening fork” in order to carry
widening loads. Pay much
attention not to overload and observe the allowable load and the capacity chart on the
truck. Careful driving should be taken when traveling and turning.
(46) When operating the machine, observe and follow all markings on the machine.
The marking plates must be replaced if lost or damaged.
(47) The forklift truck must be used under the following environment: below an
elevation of 1000 meters and temperature between -15
℃
and 35
℃
, relative humidity is
95%. Careful operation must observe under other adverse circumstances.
(48) To prevent the fire, accident or other unpredictable event, prepare the fire
extinguisher in advance and operate it according to the instructions.
(49) You can’t change or add other working equipments on the truck without our
company’s permit, or the rated capacity and safe
ty operation will be affected.
(50) Keep safety when serving on high position.
Summary of Contents for CPD10
