P/N 130426 Rev.
D
43
Banner Engineering Corp.
•
Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
A-GAGE EZ-ARRAY
Instruction Manual
Appendix
Otherwise, the Channel States data can be accessed after every
third scan (default). To set the EZ-ARRAY in Extended Cache
Mode, the register at address 41002 must be set to a value of 1.
This is a configuration register (Communications Configuration),
so this register only needs to be set once. To exit Extended
Cache Mode, the register must be set to a value of 0.
Example A–10. Writing Communications Configuration to
Enable Extended Cache Mode
Request
Response
Field Name
(Hex)
Field Name
(Hex)
Slave Address
41
Slave Address
41
Function
10
Function
10
Starting Address
(HIGH Byte)
A0
Starting Address
(HIGH Byte)
A0
Starting Address
(LOW Byte)
2A
Starting Address
(LOW Byte)
2A
Quantity of Registers
(HIGH Byte)
00
Quantity of Registers
(HIGH Byte)
00
Quantity of Registers
(LOW Byte)
01
Quantity of Registers
(LOW Byte)
01
Quantity of Bytes
02
CRC (LOW Byte)
32
Register 41002
(HIGH Byte)
00
CRC (HIGH Byte)
65
Register 41002
(LOW Byte)
01
CRC (LOW Byte)
F1
CRC (HIGH Byte)
93
A.3.4 System Info and Status
The System Info and Status section contains the current status
of the EZ-ARRAY.
Table A–40. System Info and Status
Input Register
Address
MASK
Member Name
30026
Number of Emitter Channels
30027
Emitter First Bad Channel
30028
Number of Receiver Channels
30029
RESERVED
30030
LOW BYTE
DIP Switch
30030
HIGH BYTE
ERROR Code
30031
LOW BYTE
RESERVED
30031
HIGH BYTE
Discrete Outputs
30032
Analog Output 1 DAC
30033
Analog Output 2 DAC
30034
RESERVED
Table A–41. Number of Emitter Channels
Range
Description
30-480
Number of channels the emitter has
(multiples of 30)
Table A–42. Emitter First Bad Channel
Range
Description
0-480
First channel that emitter is unable to fire
(0 = no bad channels)
Table A–43. Number of Receiver Channels
Range
Description
30-480
Number of Receiver channels (multiples of 30)
Table A–44. DIP Switch
Bit
Function
Description
0
DIP Switch 6
0 = ON, 1 = OFF
1
DIP Switch 5
0 = ON, 1 = OFF
2
DIP Switch 4
0 = ON, 1 = OFF
3
DIP Switch 3
0 = ON, 1 = OFF
4
DIP Switch 2
0 = ON, 1 = OFF
5
DIP Switch 1
0 = ON, 1 = OFF
Table A–45. ERROR Code
Value
Status
0
System OK
1
Receiver EEPROM Hard Failure
2
Receiver Alignment/Blanking Configuration Error
3
Reserved for Factory 3
4
Emitter or Wiring Problem
5
Emitter Channel Error
6
Reserved For Factory 6
7
Reserved For Factory 7
8
Reserved For Factory 8
9
Reserved For Factory 9
10
Incompatible Scan and Measurement Mode
Table A–46. Discrete Outputs
Bit
Function
Description
0
Discrete Output 1
0 = OFF, 1 = ON
1
Discrete Output 2
0 = OFF, 1 = ON
Table A–47. Analog Output 1 DAC and
Analog Output 2 DAC
Range
Description
0-4095
Current DAC value of analog output
Example continued from previous page
