Ballu-Biemmedue GE 65, Instructions Manual

Page: 13 / 29

EN
12
IMPORTANT
Before using the space heater, carefully read all of the instructions and follow them scrupulously.
The manufacturer cannot be held responsible for damage to persons and/or property caused by improper use of
the equipment.
This instruction manual is an integral part of the equipment and must therefore be stored carefully and passed on
with the unit in the event of a change of ownership.
GENERAL RECOMMENDATIONS
The space heaters run on diesel fuel. Direct combustion
versions send hot air and combustion products into the room,
while indirect combustion versions are fitted with a flue to
discharge the fumes through the chimney.
Always follow local ordinances and codes when using this
heater:
•
Follow the instructions in this booklet very carefully;
•
Use only in places free of flammable vapours or high dust
content;
•
Keep inflammable material at a safe distance from the heater
(minimum 3 metres);
•
Make sure fire fighting equipment is readily available;
•
Ensure that the machine resting surface or ground is not made
of flammable material;
•
Make sure sufficient fresh outside air is provided according to
the heater requirements. Direct combustion heaters should
only be used in well vented areas in order to avoid carbon
monoxide poisoning;
•
the indirect combustion heater is installed near a chimney to
ЭКФО КаКв ЭСО ПЮЦОЬ (ЬОО ЭСО ЩКЫКРЫКЩС “FUMES FLUE
POSITIONING DIAGRAM”) КЧН МoЧЧОМЭОН Эo КЧ ОХОМЭЫТМКХ
switchboard;
•
nothing is obstructing the aspiration and expulsion of air;
movement of air may be obstructed in various ways including
placing covers or other objects on the heater or positioning the
heater too near a wall or other large object;
•
In case of very low temperatures add kerosene to the heating
oil;
•
Make sure heater is always under surveillance and keep
children and animals away from it;
•
Before starting the heater always check free rotation of
ventilator;
•
Unplug heater when not in use.
SAFETY DEVICES
The heater is fit with an electronic device that controls the
flame and the maximum safe temperature by means of a
photocell and an overheat thermostat.
The electronic device controls start/stop times and trips the
safety in case of malfunctions. It has reset button (13) that can
assume different colours (Function Light) depending on the
function mode:
• oПП: СОКЭОЫ ТЬ ТЧ ТНХО ЦoНО oЫ ТЧ “ЬЭКЧН
-
Лв” ЦoНО, аКТЭТЧР ПoЫ
heating request;
•
steady green: heater functioning normally;
•
steady red: heater in safety stop;
•
flashing orange: heating interrupted due to excessive
variations in voltage supply (T<175V or T>265V); heating will
resume automatically when voltage returns in range from 190
V and 250 V.
Warning
To restart heating after a safety stop, push reset
button (13) for 3 seconds.
Warning
NEVER do more than two restarts in a row:
uncombusted diesel fuel may accumulate in the
combustion chamber and suddenly flare up at the
next restart.
If the safety stop persists, you have to find and eliminate the
cause of the stop before you restart the heater. Push button (13)
for at least 5 seconds to launch a self-diagnosis programme,
after which the button will assume different colours (Self-
diagnosis light) depending on the type of safety that tripped:
•
flashing orange: false flame detected during restart cycle.
•
flashing red: no flame during restart cycle.
•
flashing red/green: no flame during work cycle.
•
steady orange: internal error of electronic device.
Warning
See
“TROUBLESHOOTING” Эo ТНОЧЭТПв ЭСО М
ause of
the malfunction.
OPERATION
Before switching on the heater and, therefore, before plugging
it into the electrical power supply, check that the power supply
specifications are the same as those stated on the identification
plate.
Warning
For mode
Хs “DV” МСОМФ ЭСКЭ ЭСО Кrroаs oЧ ЭСО
voltage supply selector key cover are pointing to
the voltage value required.
If necessary:
• rОЦoЯО ЭСО МoЯОr;
• prОss НОПХОМЭor (
18) to the position required;
• rОpХКМО ЭСО proЭОМЭТЯО МoЯОr.
Warning
To operate the machine, must install the air
dispersion cone (19) on the front of the machine as
shown in the fi
РЮrО КЛoЯО (“OpОrКЭТЧР НТКРrКЦ”).
Warning
•
The power line must be earthed and fitted with a
residual current circuit breaker.
•
The heater plug must be inserted into a socket
equipped with a mains switch.
The heater must be placed on a flat, stable, and levelled
surface in order to prevent it from overturning and/or diesel leaks
from the tank filler cap.
You can run the generator in manual by setting switch (14) to
ON.
The generator can only work automatically when a control
device, such as for example a thermostat or a timer, is connected
to the heater.