background image

RELEASE DATE

2-26-19

REFERENCE

 

NUMBER

INS-2791-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900 

www.bklighting.com • [email protected]

B-K LIGHTING

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

NEMA 3R Remote Driver

10W Solid State LED

Installation Instructions

4.  Connect conduit connector through female 

threaded conduit entry. 

 NOTE: Surface conduit is a common entrance 

for water if not properly sealed. Seal 

connector threads and conduit with a suitable 

sealant (Teflon tape, adhesive, etc.). Sealing 

the conduit after knockouts are removed is 

required to maintain warranty.

8.  Re-attach cover. Tighten cover screw.

5.  Pull branch circuit wiring necessary for 

installation (By Others).

Single Remote Driver

7.  Connect branch circuit to terminal block.  Connect incoming ground to ground wire provided on NEMA 3R 

housing.  Connect secondary leads to terminal.  See labels on terminal block for additional information.

6.  Pull secondary lamp leads necessary for 

installation though dedicated conduit. (By 

Others).

NOTE: Failure to comply with specific wiring 

requirements will void product warranty.

2.  Attach the NEMA 3R housing at mounting holes 

with ¼” fasteners (By Others). Use suitable 

mounting hardware for surface. Use level to 

ensure a level install.

 NOTE: Many methods exist to bolt to a 

flat surface. The housing is provided with 

mounting brackets with ¼” holes.

Housing Installation

3.  Remove Knockout(s) with hammer as needed 

from the NEMA 3R housing. Leave remaining 

unused knockouts in place to maintain seal.

1.  Remove cover by removing #10-24 cover screw 

using a 1/8” Allen wrench.

Summary of Contents for SARATOGA Series































Reviews: