7. Attach tether wire under screw head at the base
of the UPM housing and tighten. Slowly lower
the faceplate until tether is taut.
NOTE: Faceplate tether supplied with UPM
is designed as an installation aid and NOT a
safety cable. Do not add weight to, or drop
faceplate.
RELEASE DATE
2-27-19
REFERENCE
NUMBER
INS-2795-02
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
Ground
Hot
Neutral
A
B
C
Ground
Hot
Neutral
6. If UPM housing is not level, remove UPM housing;
loosen but
DO NOT REMOVE
(2) #8-32 screws
with 9/64” Allen wrench on CamLock™ assembly.
Adjust CamLock™ assembly up to 30° as needed
to level. Tighten the screws and reattach UPM
housing.
10. Make sure UPM body gasket is free of any dirt or
debris. Attach the faceplate by tightening the (4)
#6-32 captive screws evenly using a 5/64” Allen
wrench.
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Ground
Hot
Neutral
A
B
C
Ground
Hot
Neutral
A
B
C
Ground
Hot
Neutral
A
B
C
1. Install standard 4.5” x 2.85” recessed junction box
(By Others) in the final fixture location according
to designed lighting plan.
NOTE: Vertical or horizontal installation of
recessed junction box determines orientation
of UPM.
2. Pull branch circuit wiring necessary for
installation (By Others.)
3. Feed branch circuit wiring and lamp leads to
remote mounted fixture through mounting plate
with CamLock™ assembly. Attach mounting plate
with supplied (2) #6-32 stainless steel hex drive
fasteners to recessed junction box using a 5/64”
Allen wrench.
4. Feed wire into UPM housing. Install housing
on CamLock™ at 90° to finished orientation as
shown. (Figure A)
5. Rotate housing 90° counter-clockwise (Figure
B). Tighten set screw with 5/64” Allen wrench
on outside of UPM housing to lock in place.
(Figure C)
Installation Instructions
PM2DRM RECTANGULAR CAMLOCK™
10W Dual Driver Housing
LINE
Red
FIXTURE
COM
Hydrolock
Plate
Black
GROUND
Driver
White
Black
Green
DIM +
DIM -
Black
White
Hydrolock
Plate
Green
Driver
White
Black
White
Blue
Green
LINE
COM
GROUND
Orange
Orange
Brown
Blue
Black
Gray
FIXTURE
FIXTURE
Green
Green
LINE
Red
FIXTURE
COM
Driver
Black
GROUND
DIM +
DIM -
GROUND IN HOUSING
LINE
Red
FIXTURE
COM
Driver
Black
DIM +
DIM -
GROUND ON PLATE
LINE
Red
FIXTURE
COM
Driver
Black
DIM +
DIM -
HP2RM
HP2 TR
TMB
PCIII
Generic TR
GROUND IN HOUSING
LINE
Quick
Connect
COM
Driver
FIXTURE
DIM +
DIM -
PM3
GROUND IN HOUSING
LINE
Quick
Connect
COM
Driver
FIXTURE
DIM +
DIM -
Quick
Connect
Driver
FIXTURE
DIM +
DIM -
PM3D
GROUND IN HOUSING
LINE
COM
Remote
Driver
DIM +
DIM -
Fixture
Fixture
GROUND ON PLATE
LINE
COM
Driver
DIM +
DIM -
PCIII
Quick
Connect
FIXTURE
LINE
Red
FIXTURE
COM
Remote
Driver
Black
DIM +
DIM -
MA/AP
GROUND
GROUND IN HOUSING
LINE
COM
Remote
Driver
DIM +
DIM -
DIM +
DIM -
Fixture
Fixture
Remote
Driver
Fixture
Fixture
LINE
COM
Remote
Driver
GROUND
F
Fixture -
GROUND IN HOUSING
LINE
COM
Remote
Driver
F
Fixture -
Remote
Driver
F
Fixture -
GROUND IN HOUSING
LINE
COM
Remote
Driver
F
Fixture -
WIRING DIAGRAM - 010 Control Type
9. Use waterproof wire connectors (By Others) to
connect driver primary leads to branch circuit
wires. Connect incoming ground to ground wire
provided in UPM housing. Connect incoming
dimming control wires to driver dimming
controls. Connect secondary leads to fixture
leads.
See wiring diagram.
LINE
Red
FIXTURE
COM
Hydrolock
Plate
Black
GROUND
Driver
White
Black
Green
DIM +
DIM -
Black
White
Hydrolock
Plate
Green
Driver
White
Black
White
Blue
Green
LINE
COM
GROUND
Orange
Orange
Brown
Blue
Black
Gray
FIXTURE
FIXTURE
Green
Green
LINE
Red
FIXTURE
COM
Driver
Black
GROUND
DIM +
DIM -
GROUND IN HOUSING
LINE
Red
FIXTURE
COM
Driver
Black
DIM +
DIM -
GROUND ON PLATE
LINE
Red
FIXTURE
COM
Driver
Black
DIM +
DIM -
HP2RM
HP2 TR
TMB
PCIII
Generic TR
GROUND IN HOUSING
LINE
Quick
Connect
COM
Driver
FIXTURE
DIM +
DIM -
PM3
GROUND IN HOUSING
LINE
Quick
Connect
COM
Driver
FIXTURE
DIM +
DIM -
Quick
Connect
Driver
FIXTURE
DIM +
DIM -
PM3D
GROUND IN HOUSING
LINE
COM
Remote
Driver
DIM +
DIM -
Fixture
Fixture
GROUND ON PLATE
LINE
COM
Driver
DIM +
DIM -
PCIII
Quick
Connect
FIXTURE
LINE
Red
FIXTURE
COM
Remote
Driver
Black
DIM +
DIM -
MA/AP
GROUND
GROUND IN HOUSING
LINE
COM
Remote
Driver
DIM +
DIM -
DIM +
DIM -
Fixture
Fixture
Remote
Driver
Fixture
Fixture
LINE
COM
Remote
Driver
GROUND
F
Fixture -
GROUND IN HOUSING
LINE
COM
Remote
Driver
F
Fixture -
Remote
Driver
F
Fixture -
GROUND IN HOUSING
LINE
COM
Remote
Driver
F
Fixture -
WIRING DIAGRAM - INC Control Type
8. Use waterproof wire connectors (By Others) to
connect driver primary leads to branch circuit
wires. Connect incoming ground to ground
wire provided in UPM housing. Connect
secondary leads to fixture leads.
See wiring
diagram.
