AVZ Cubola Solidare Installation Instruction Download | Manualshive

Page: 15 / 31

background image

Cubola

®

Solidare

®

EN 20-04-2018

15

5.

Take the tensioning wire through the tensioning wire mounting blocks and the cover profile. Fasten
the tensioning wire mounting blocks in the clamping plate with M8x25 bolts. Note: Make sure the
mounting blocks are centered under the front profile.

6.

Keep at both sides of the mounting block and the cover profile a distance of 2 mm. Fasten the cover
profile through the holes of 6,5 mm.

7.

Fasten the hexagon connection nut with a washer to the side of the tensioning wire with screw-
thread. On the other side the clamping sleeve with wedge set is positioned.

8.

Turn the hexagon connection nut tight to tension the front profile straight.

«
...
13
14
15
16
17
...
»

Summary of Contents for Cubola Solidare
































Reviews:

No comments

Related manuals for Cubola Solidare

Brand: Best Pages: 28

Hayling 4 AIR TC

Brand: Kampa Pages: 64

Brand: Blacks of Greenrock Pages: 4

Brand: Blacks of Greenock Pages: 6

CANOPIA PALERMO 10x10 / 3x3

Brand: Palram Pages: 56

Brand: Dancover Pages: 20

Brand: Vango Pages: 3

Brand: Zolia Pages: 3

Brand: Coleman Pages: 2

ZEKU-L INNER TENT

Brand: ZANE ARTS Pages: 12

Scenic Pass 2 Scenic Pass 2

Brand: Eureka Pages: 2

Brand: Eureka Pages: 1

Brand: Backyard Discovery Pages: 30

Brand: Systems Trading Corporation Pages: 18

Brand: Big Game Treestands Pages: 2

VITABRI Canopies AIR TENT

Brand: Ins'Tent Pages: 2

TaB Clamshell Tent

Brand: PahaQue Wilderness Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands