Avidyne Entegra EX5000 Installation Manual Download Page 5

Page: 5 / 114

EX5000 Release 8.2.2 Installation Manual P/N 600-00073-001 Rev 02

- 5 -

5.13.2

Setup with GPS/FMS as Heading Source

.................................................................... 77

5.13.3

Setup with StormScope as Heading Source

................................................................ 77

5.13.4

Setup with Traffic (TAS) as Heading Source

............................................................... 77

5.13.5

Map Orientation with Track

............................................................................................. 77

5.13.6

Map Heading/Track Status

............................................................................................. 78

Post-Installation Check

......................................................................................................... 79

6.1

System Info Pages

................................................................................................................... 79

6.1.1

System Info Platform Page

............................................................................................. 79

6.1.2

System Info Port Page

..................................................................................................... 79

6.2

Electro-Magnetic Compatibility (EMC) Check

...................................................................... 80

6.3

TWX670 Lightning Sensor Strike Test

.................................................................................. 80

6.4

WX-500 Lightning Sensor Strike Test

................................................................................... 81

6.5

Traffic Test

................................................................................................................................. 81

6.6

XM Broadcast Datalink Satellite Reception Confirmation

.................................................. 81

6.7

Magnetic Compass Swing

...................................................................................................... 82

MFD General Maintenance

.................................................................................................... 83

7.1

Cleaning the EX5000 Screen

................................................................................................. 83

7.2

MFD Data Updates

.................................................................................................................. 83

7.2.1

Loading NavData (the Navigation Database)

.............................................................. 84

7.2.2

Loading CMax Chart Data

.............................................................................................. 84

7.2.3

Downloading EMax Data

................................................................................................. 85

Avidyne Technical Support and Service

............................................................................ 87

8.1

Technical Support

.................................................................................................................... 87

8.2

Service

....................................................................................................................................... 87

Appendix A: Environmental Qualification Data

........................................................................ 88

Appendix B: Flight Manual Supplement Information

............................................................... 90

Appendix C STC Permission

........................................................................................................ 91

Appendix D: Landscape EX5000 Dimensions

........................................................................... 92

Appendix E: Landscape EX5000 with Integrated Datalink Dimensions

................................ 93

Appendix F: Portrait EX5000 Dimensions

................................................................................. 94

Appendix G: Landscape Cutout Dimensions

............................................................................ 95

Appendix H: Portrait Cutout Dimensions

.................................................................................. 96

Appendix I: Wiring Diagram – Power, Dimming Bus, and Exceedance Horn

...................... 97

Appendix J: Wiring Diagram – GPS/FMS

................................................................................... 98

Appendix K: Wiring Diagram – Lightning and Broadcast Datalink

..................................... 100

Summary of Contents for Entegra EX5000



















































































































Search results

Summary of Contents for Entegra EX5000

Reviews:

Related manuals for Entegra EX5000

Brands by name

Popular brands

Avidyne Entegra EX5000, Installation Manual

Search results

Summary of Contents for Entegra EX5000

Reviews:

Related manuals for Entegra EX5000

Brands by name

Popular brands