Avidyne Entegra EX5000 Installation Manual Download Page 11

Page: 11 / 114

EX5000 Release 8.2.2 Installation Manual P/N 600-00073-001 Rev 02

- 11 -

2.2 MFD Technical Specifications

Table 1: MFD Technical Specifications

Standard Features

Display

High Brightness Color Active Matrix LCD, sunlight readable

Diagonal size

10.4 inches

Resolution

SVGA 800 X 600

Interfaces

RS-232, USB

Viewing angle (Landscape)

60 degrees horizontal, +45/-15 degrees vertical

Viewing angle (Portrait)

60 degrees vertical, +45/-15 degrees horizontal

Optional Interfaces

EX5000-Series only

RS-232, ARINC 429, ARINC 453, and TTL

Physical Characteristics

Weight

700-00004-001/002/007/008/009/010

700-00030-805

6.4 lbs

700-00004-004/005/006
700-00030-005

7.6 lbs (with Narrowcast)

700-00004-104

7.6 lbs (with Narrowcast)

CG from Instrument Panel (Landscape)

700-00004-001/002/007/008/009/010
700-00004-004/005/006
700-00030-005

1.60 inches

CG from Instrument Panel (Portrait)

700-00004-104

1.60 inches

CG from Instrument Panel (Landscape)

1.60 inches

Height (Landscape)

8.50 inches

Height (Portrait)

11.0 inches

Width (Landscape)

10.7 inches

Width (Portrait)

7.8 inches

Depth

700-00004-001/002

4.3 inches (3.7 inches behind the panel)

700-00004-004/005/006/007/008/009/010/104
700-00030-005/805

5.2 inches (4.6 inches behind the panel)

Electrical Requirements

Voltage

18-35 VDC, negative ground

Current

700-00004-001/002/007/008/009/010
700-00030-805

Maximum 3.5 A at 28V

700-00004-004/005/006/104
700-00030-005

Maximum 4.0 A at 28V

Cooling Requirement

Unrestricted airflow to the top and bottom of the landscape chassis
or both sides of portrait chassis.

Operating Limits

See

Appendix A: Environmental Qualification Data

TSOs

See Table 2: TSOs by Software Part Number.

Summary of Contents for Entegra EX5000



















































































































Search results

Summary of Contents for Entegra EX5000

Reviews:

Brands by name

Popular brands

Avidyne Entegra EX5000, Installation Manual

Search results

Summary of Contents for Entegra EX5000

Reviews:

Brands by name

Popular brands