Avaya H239 Installing And Administering Download | Manualshive

Page: 7 / 62

background image

Chapter 1: Introduction

Purpose

This document provides procedures for installing, configuring, administering, and troubleshooting
the Avaya H239 and H249 phones. This document is primarily intended for implementation
engineers and administrators.

Change history

This section describes the key changes since the first issue of this document. This section is not
included in new documents that have not been updated since the first issue.

Issue

Date

Summary of changes

Issue 1

April 2018

First issue of this document for the initial release.

Table continues…

October 2019

Installing and Administering the Avaya H239 and H249 Phones

7

Comments on this document? [email protected]

«
...
5
6
7
8
9
...
»

Summary of Contents for H239































































Reviews:

No comments

Related manuals for H239

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 42

Brand: Panasonic Pages: 135

Brand: Uniden Pages: 88

Brand: Uniden Pages: 42

980590-0403 - Cordless Internet Handset USB VoIP Wireless Phone

Brand: Logitech Pages: 2

Brand: Alcatel Pages: 2

3100 ICP - 4.0 L

Brand: Mitel Pages: 18

Brand: AT&T Pages: 15

Brand: Radio Shack Pages: 24

AIDE MEMOIRE M7455

Brand: Aastra Pages: 2

Brand: GE Pages: 2

Brand: GE Pages: 40

Brand: GE Pages: 80

Brand: GE Pages: 2

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands