background image

Chapter 5: Phone settings configuration

and management

You must configure the phone before it can be used. Mandatory configuration tasks include
configuring the IP address, and using the web portal to set up SIP settings and memory key
settings.

You can also perform other configuration and management tasks on the web portal.

Configuring automatic phone provisioning

About this task

Automatic provisioning is useful for configuring firmware for a large number of phones.

Before you begin

Ensure that the file server is set up.

Procedure

1. From the 

Avaya Support

 website, download the latest firmware file for your phone.

2. Copy the downloaded firmware file to the file server.

3. From the 

Avaya Support

 website, download the configuration file template.

The file name is 

f0H2xxhw1.100.cfg

, where 

H2xx

 is the phone model.

4. In the AUTOUPDATE CONFIG MODULE section of the configuration file template, add

Auto Image Url

 with the path of the firmware file.

For example: 

Auto Image Url: http://172.16.6.39/

hotelh2s2.4.0.5379T20180209153130.z

October 2019

Installing and Administering the Avaya H239 and H249 Phones

42

Comments on this document? [email protected]

Summary of Contents for H239































































Reviews: