background image

Reliability and Recovery

256 Avaya Application Solutions IP Telephony Deployment Guide

 

Assessment Methodology and Criteria

The availability of a subsystem is described by the following equation:

where MTBF represents Mean Time Between Failures and MTTR represents Mean Time to 
Recover/Repair. MTTR is the time to diagnose, respond, and resume service.

This equation is also sometimes presented in industry literature as the following:

where MTTF is defined as Mean Time to Failure, and equates to (MTBF - MTTR).

Using the above equation, the estimated average annual minutes of downtime experienced due 
to a subsystem failure can be expressed as:

(Based on assuming 365.25 days in a year, There are 365.25 

×

 24 

×

 60 = 525960 minutes in a 

year).

For projecting a enterprise’s total system availability, the sum of annual downtime contributed 
from all subsystems is calculated, and then the system availability is estimated by using this 
sum.

Note that this formula will result in a crude approximation of availability, as it does not account 
for the groups of subsystems whose downtimes overlap. 

Definition of Critical Outages and Downtime

The industry recognized criteria used for defining failure, outages and the downtime minutes 
experienced is based on the Telecordia (Bellcore) GR-512 Reliability Model requirements for 
telecommunications equipment.

Availability

MTBF

MTTR

(

)

MTBF

----------------------------------------------

=

Availability

MTTF

(

)

MTTF

MTTR

+

(

)

----------------------------------------------

=

AnnualDowntimeMinutes

1

Availability

(

)

525960minutes / year

(

)

×

=

TotalSystemAvailability

1

i

th

SubsystemContributedMinuteDowntime

[

]

i

525960Minutes / Year

------------------------------------------------------------------------------------------------------------------------------------

=

Summary of Contents for Application Solutions





































































































































































































































































































































































































































Reviews: