background image

4

Dual Gate Controller DCB-05 

Owner Installation Instructions

FOR ADDITIONAL SAFETY

 protection we strongly recommend the fi tting of a Photo Electric  

(PE) Beam. In most countries PE Beams are mandatory on all gates fi tted with automatic 

openers. For a small additional outlay Automatic Technology recommends that Photo 

Electric Beams be installed with the automatic opener ensuring additional safety and 

peace of mind.

DO NOT

 operate the gate opener unless the gate is in full view and free from objects such as 

cars and children/people. Make sure that the gate has fi nished moving before entering or 
leaving the driveway. 

DO NOT 

operate the gate opener when children/people are near the gate. Children 

must be supervised near the gate at all times when the gate opener is in use. 

Serious 

personal injury

 and/or property damage can result from failure to follow this warning.

DO NOT

 allow children to operate the gate opener. 

Serious personal injury

 and/

or property damage can result from failure to follow this warning.

Make sure that the 

safety obstruction detection 

system is working correctly, 

and is 

tested

 every month. Test as per the Installation Instructions Manual. 

Adjust if necessary and recheck. Failure to follow this rule could result 
in 

serious personal injury 

and/or property damage. This test must be 

repeated at regular intervals and the necessary adjustments made as 
required.

DO NOT

 disengage the gate opener to manual operation with 

children/people or any other objects including motor vehicle 
within the gateway. 

If using a key switch or keypad or any device that can operate 
the gate opener, make sure it is out of reach of children and 
that the gateway is in full view at all times. 

If the power supply cord is damaged, it 

must

 be 

replaced by an Automatic Technology service agent 
or suitably qualifi ed person. 

Make sure that remote controls are kept out of 
reach of children.

WARNING: It is vital for the safety of persons to follow 
all instructions. Failure to comply with the following 
Safety Rules may result in serious personal injury and/or 
property damage.

Important safety instructions

Summary of Contents for DCB-05









































Reviews: