Autel MaxiDAS DS808TS Manual Download Page 130

Page: 130 / 167

123

Settings

Tap the Settings button to adjust the default settings and view information
about the MaxiDAS system:



Unit



Language



Printing Setting



Notification Center



Auto Update



About



System Settings

This section describes the procedures

to adjust the device’s system settings.

Unit

This option allows you to adjust the measurement unit for the diagnostic
system.



To adjust the unit setting

1. Tap the

Settings

application on the MaxiDAS Job Menu.

2. Tap the

Unit

option on the left column.

3. Select the desired measurement unit, Metric or English. A tick icon

will display to the right of the selected unit.

4. Tap the

Home

button on the top left corner to return to the MaxiDAS

Job Menu. Or tap another setting to adjust.

Summary of Contents for MaxiDAS DS808TS








































































































































































Search results

Summary of Contents for MaxiDAS DS808TS

Reviews:

Related manuals for MaxiDAS DS808TS

Brands by name

Popular brands

Autel MaxiDAS DS808TS, Manual

Search results

Summary of Contents for MaxiDAS DS808TS

Reviews:

Related manuals for MaxiDAS DS808TS

Brands by name

Popular brands