background image

ZONEMIX

 INSTALLATION AND OPERATION MANUAL

9

FRONT PANEL CONTROLS

AUDIO SETUP

•  Input 1 Mode   

Line/Mic/Mic+Phantom

•  Input 2 Mode   

Line/Mic/Mic+Phantom

•  Input 3 Pad (-14dB) 

Enabled/Disabled

•  Input 4 Pad (-14dB) 

Enabled/Disabled

•  Input 5 Pad (-14dB) 

Enabled/Disabled

•  Input 6 Pad (-14dB) 

Enabled/Disabled

•  Output Bass   

Zone1-8 ±10dB

•  Output Treble   

Zone1-8 ±10dB

TONE GENERATOR

The ZONEMIX includes 5 factory programmed default tones. Tones can be played by shorting the appropriate contact to GND on the 
back panel 10 way euroblock connector.
 

 The tone volume is set by adjusting the Tone/Message input level control on the front panel or software

 

 The internal tones can be optionally overridden by placing files on an SD card

 

 IMPORTANT: Do NOT drive external voltages into the pins or damage to the unit will occur. 

TONES

1.  ‘EVAC’: a long continuous repeating tone with a ramped frequency.  

Triggered by shorting EVAC to GND, the sound will continue to repeat until the short is released. 

2.  ‘ALERT’: a short tone burst tone repeated every 0.5s.  

Triggered by shorting ALERT to GND, the sound will continue to repeat until the short is released. 

3.  ‘INTRUDER’: a two tone ‘low’ ‘high’ alert repeating every 0.4s.  

Triggered by shorting INTRUDER to GND, the sound will continue to repeat until the short is released. 

4.  ‘BELL’: a short repeating tone burst with decay and reverb.  

Triggered by shorting BELL to GND, the sound will continue to repeat until the short is released. 

5.  ‘CHIME’: a four note increasing tone suitable for paging preannounce.  

Triggered by shorting CHIME to GND, it will sound only once each time the trigger is activated. Please note: ‘CHIME’ tone must 
play to completion before it may be retriggered. 

•  To activate a tone trigger input, short the relevant input to GND. The selection must be stable for longer than 150ms. 
•  Each tone is played to completion even if the trigger selection is removed during playback. 
•  A higher priority tone trigger will interrupt a lower priority tone being played. 
•  After deselection and completion of playing a higher priority tone, any selected lower priority tone will be played. Exceptions are 

BELL and CHIME tones which will not be played and must be re-triggered.

 DURING TONE PLAYBACK: 

> EVAC, ALERT and INTRUDER tone playback mute all input channels (except a Master Override input) 
> BELL and CHIME tone playback will mute or mix with other inputs depending on Priority Confugration settings.

SYSTEM SETUP

•  Date/Time
•  Display Brightness
•  Display Contrast
•  RS232 Baud Rate
•  Serial Number
•  MAC Address
•  IP Address
•  Host Name
•  Firmware Version
•  Reset network configuration
•  Reset Admin account login
•  Reset to factory defaults

The following settings can be viewed or modified using the front panel menus

Summary of Contents for 9323383020634

































Reviews: