manualshive.com logo in svg

AUSTRALIAN MONITOR 9323383020634, Installation And Operation Manual

Share
Download
AUSTRALIAN MONITOR 9323383020634 Installation And Operation Manual Download Page 10

ZONEMIX

 INSTALLATION AND OPERATION MANUAL

10

SD CARD

OVERRIDING DEFAULT TONE GENERATOR SOUNDS

The default tones of the ZONEMIX can be overridden by adding tones to a user supplied SD card. Simply place the tone WAV file on 
the root of the SD card and it will be played instead of the inbuilt tone. 
 

Format: evac.wav, alert.wav, intruder.wav, bell.wav, chime.wav

 

 Only WAV files are supported. Do NOT use MP3 or other audio formats

 
NOTE: If the tone on the SD card is unplayable, e.g due to being the wrong format, a fault code will flash on the    

 

 

STATUS LED and the default tone will be played instead. 

PAGING & SCHEDULER ANNOUNCEMENTS

Pre-recorded paging announcements and scheduler messages can be programmed for playback via the control software.
Place audio WAV files on the root of the SD card.
The audio files can then be selected using the ZONEMIX control software file explorer menu.

 

Format: message.wav 

 

 Only WAV files are supported. Do NOT use MP3 or other audio formats

CUSTOM PAGING CHIME

The ZMPS paging station chime can be optionally overridden by placing an alternative file on the root of the SD card. 
 

Format: pagingchime.wav 

 

 Only WAV files are supported. Do NOT use MP3 or other audio formats 

SUPPORT OF SD CARDS LARGER THAN 32GB

The ZONEMIX supports the FAT32 file format which is limited to a maximum of 2TB.
However, SD cards larger than 32GB are shipped with the exFAT format. These must be reformatted to the FAT32 format.

 

 NOTE: Windows does NOT natively support formatting of SD cards larger than 32GB to FAT32.

 

 You must use third party applications to format SD cards larger than 32GB to the required FAT32 format.

PC CONTROL SOFTWARE

The ZONEMIX comes with a free PC application to allow advanced configuration and control of the system. The software can be 
downloaded from www.australianmonitor.com.au and can be accessed from either the USB or Ethernet connection.

USB CONNECTION

1.  Simply connect the supplied USB cable from your PC to the ZONEMIX front panel connector.
2.  Open the ZONEMIX Control Software
3.  Select the device from the USB port dropdown list and select CONNECT

 

 Note: If the ZONEMIX does not show in the list press the DISCOVER button to perform a re-scan.

ETHERNET CONNECTION

The ZONEMIX can also be controlled over a network using the ethernet port. By default, the ZONEMIX uses DHCP to be 
automatically assigned an address from the network. The PC Control Software will then scan the network and list available devices for 
connection.
If no address is provided by the network the ZONEMIX will default to an IP address of 192.168.1.10.

PLUG AND PLAY (DYNAMIC/DHCP IP)

1.  Connect an Ethernet cable from the ZONEMIX to the network
2.  Open the ZONEMIX Control Software
3.  Select the device from the Ethernet dropdown list and select CONNECT

 

Note: If the ZONEMIX does not show in the list press the RESCAN FOR DEVICES button to perform a re-scan. 

 

 Note: If the ZONEMIX still does not show, confirm the network has assigned an IP address by accessing the front panel  
System Setup menu and viewing the IP address. If the ZONEMIX states it’s IP address is 192.168.1.10 it has failed to get an 
address and gone to the default address 

Summary of Contents for 9323383020634

































Reviews:

No comments

Brands by name

Popular brands

Load more brands