Audi TT COUPE Service Download Page 88

Page: 88 / 92

Service

1.8 T

(132 kW)

1.8 T quattro

(165 kW)

Length of luggage com-
partment with rear seat
folded down

1397

1360

Height of luggage comp.

764

660

Luggage compartment vol.

272/547

218/493

Vert. headroom,
front/rear

49/-87

Max. seating height,
front/rear

959/828

Elbow room, front/rear

1412/1221

Weights

Kerb weight (w/o driver)

1205

1395

Max. perm. gross weight

1575

1765

Payload

370

Max. permissible axle load, front/rear

940/735

1015/850

Max. permissible roof load

Capacities

Cooling system capacity

Engine oil capacity

4 ltr. and 4.5 ltr. without and with ﬁlter change respectively

Gearbox oil capacity

fwd: 2.3

quattro: 2.6

Tank capacity

Windscreen washer
ﬂuid tank

4 l (3.74 ltr. usable water volume)

Performance/consumption/acoustics

Max. speed

kph

228

243

at engine speed

rpm

6430

6281

Acceleration

0-80 kph

5.5

4.3

0-100 kph

7.4

6.4

Elasticity in 4th/5th gear
(5th/6th gear for 165 kW engine)

60-120 kph

9.9/13.1

11.2/14.8

Fuel type

Premium unleaded 98 RON

Consumption acc. to 93/116/EC

Urban cycle

ltr./100 km

10.9

Out-of-town cycle

ltr./100 km

6.3

Overall

ltr./100 km

8.0

9.2

CO2 emission

g/km

192

221

Theoret. range (MVEG)

687

674

Summary of Contents for TT COUPE




























































































Search results

Summary of Contents for TT COUPE

Reviews:

Related manuals for TT COUPE

Brands by name

Popular brands

Audi TT COUPE, Service

Search results

Summary of Contents for TT COUPE

Reviews:

Related manuals for TT COUPE

Brands by name

Popular brands