Audi TT COUPE Service Download Page 38

Page: 38 / 92

External and internal torque requests are co-
ordinated by the engine control unit, making
allowance for efﬁciency and implemented with
the available manipulated variables.

Torque-oriented engine
management

The Motronic ME 7.5 has a torque-ori-
ented functional structure.
The new electronic throttle control
function makes this possible.

Internal
torque requests

External torque requests

•

art

•

Idling control

•

Catalytic converter
heating

•

Power output
limitation

•

Driving comfort

•

Component
protection

•

Engine speed
limitation

•

Driver input

Throttle valve

angle

Charge pressure

Ignition angle

Cylinder suppres-

sion

Injection time

Torque-inﬂuencing manipula-
ted variables

•

Driving
dynamics

•

Driving
comfort

•

Cruise control
system

Co-ordination of tor-

que and efﬁciency

requests in the engine

control unit

SSP207/96

Subsystems of the Motronic

Summary of Contents for TT COUPE




























































































Search results

Summary of Contents for TT COUPE

Reviews:

Related manuals for TT COUPE

Brands by name

Popular brands

Audi TT COUPE, Service

Search results

Summary of Contents for TT COUPE

Reviews:

Related manuals for TT COUPE

Brands by name

Popular brands