Athena 1090 EVO Translation Of Original Instructions Download Page 100

Page: 100 / 182

100

Preliminary notes:

The system is active only when the platform floor is higher than 2mt

The system is active only within 3° of inclination

The system is active only if the work platform is below the maximum

travel height of 4.5 mt platform floor (scissor frame angle with respect to
frame 23°)

If indicator light 1 is off, it means that the inclination is less than 0.5°

If indicator light 1 is flashing, it means that the inclination is greater than

0.5° and less than 3°

If indicator light 1 is on, it means that the inclination is greater than 3° or

that the inclination is greater than 0.5° and the work platform is higher
than the maximum travel height.

Warning: the Proactive levelling is active only if light 1 is flashing or off.

Summary of Contents for 1090 EVO























































































































































































Search results

Summary of Contents for 1090 EVO

Reviews:

Athena 1090 EVO, Translation Of Original Instructions, Page: 100 / 182

Search results

Summary of Contents for 1090 EVO

Reviews: