Atec Solmetric SunEye 210 User Manual Download Page 83 | Manualshive

Page: 83 / 90

background image

5-3

Maintenance and Troubleshooting

Compass Calibration

Figure

5-2.

Compass Calibration Menu

4

Perform the calibration as indicated by the directions on the SunEye. The level indicator must be
centered and locked (yellow) for the calibration point to be accepted. Two measurements are
made at positive and negative tilts for the Northern orientation. Tilt the SunEye so that the level
indicator is centered and locked. Figures below are examples of what needs to be performed for
the Northern orientation.

Figure

5-3.

Compass Calibration

Figure

5-4.

Compass Calibration

«
...
81
82
83
84
85
...
»

Summary of Contents for Solmetric SunEye 210



























































































Reviews:

No comments

Related manuals for Solmetric SunEye 210

Brand: Keithley Pages: 148

Brand: Kawai Pages: 33

Brand: Kawai Pages: 60

Brand: GE Pages: 35

Brand: Yamaha Pages: 24

Brand: Hanna Instruments Pages: 2

Brand: DODODUCK Pages: 2

Brand: Spasciani Pages: 26

Brand: ACE INSTRUMENTS Pages: 6

Brand: Omega Pages: 20

Brand: JUMO Pages: 150

Brand: sebaKMT Pages: 131

Brand: Hanna Instruments Pages: 2

Brand: Vogel Pages: 4

K-PATENTS PR-23 AX Series

Brand: Vaisala Pages: 246

Brand: Omega Pages: 59

Brand: Niigata seiki Pages: 2

Brand: Kapro Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands