Asus RS720-E7-RS24-EG User Manual Download Page 81

Page: 81 / 202

ASUS RS720-E7-RS24

5-5

The utility verifies the file, then starts updating the BIOS file.

DO NOT shut down or reset the system while updating the BIOS to prevent system boot

failure!

The utility returns to the DOS prompt after the BIOS update process is completed.

Reboot the system from the hard disk drive.

The BIOS update is finished! Please restart your system.
C:\>

ASUSTek BIOS Update for DOS V1.06 (09/08/04)

Current CAP

Update CAP

Note

Writing BIOS:

FLASH TYPE:

MXIC 25L1605A

PATH:

BOARD:

Z9PE-D16-10G/DUAL

VER:

0201

DATE:

12/01/2013

BOARD:

Z9PE-D16-10G/DUAL

VER:

0202

DATE:

12/09/2013

WARNING! Do not turn off power during flash BIOS

Summary of Contents for RS720-E7-RS24-EG











































































































































































































Search results

Summary of Contents for RS720-E7-RS24-EG

Reviews:

Brands by name

Popular brands

Asus RS720-E7-RS24-EG, User Manual

Search results

Summary of Contents for RS720-E7-RS24-EG

Reviews:

Brands by name

Popular brands